Shop Now, Pay Later with Affirm. Learn More

Radial Engineering
Voco-Loco Effects Switcher

Be the first to review this product

Item: N13-1981

Availability: Out of stock

Voco-Loco Effects Switcher
Voco-Loco Effects Switcher Voco-Loco Effects Switcher Voco-Loco Effects Switcher


The Voco-Loco is a foot-controlled effects loop that enables the lead vocalist, sax or trumpet player to incorporate guitar effects pedals into the signal path, just like an electric guitarist adds effects for soloing.

The design begins with a state-of-the-art mic preamp that is designed to accept both a standard dynamic microphone or a condenser by activating the built-in phantom power supply. A great sounding two band EQ with low and high frequency shelving makes it easy to add warmth and shimmer. The signal is then sent to the guitar pedals via a transformer isolated hi-Z effects loop circuit that is equipped with individual send & receive controls to optimize signal-to-noise and reduce distortion. A tone control on the return path lets you smooth the sound of pedals that may be overly bright and the blend control lets you mix the original 'dry' signal with the 'wet' effect to set the perfect mix.

Simply plug your mic into the Voco-Loco via the XLR input, connect your effects pedals using standard ¼" guitar cables, and then send the output from the Voco-Loco to the input on your mixer. Before the song begins, choose which effects you want on and - when you are ready - activate the loop using the right hand footswitch. A second footswitch serves double-duty as either a mute switch to turn off the mic between sets or as a 100% wet effects loop for special situations where you may not want any of the clean signal to pass through.

With the Voco-Loco in your signal chain, you can add delay or reverb, maybe a touch of distortion or even a special effect like a wah-wah to enhance your solo performance. The options are only limited by your imagination and desire to stand out from the crowd!


  • Add guitar effects pedals to vocals or instruments
  • Create exciting and unique effects as you perform
  • Turn on multiple effects using one footswitch
  • Works with either dynamic or condenser microphones

Questions on Voco-Loco Effects Switcher

No questions asked yet

Ask Your Own Question


  • Audio circuit type: Integrated Op-Amp with Class A FET input circuit
  • Frequency response: 20Hz ~ 20kHz
  • Total harmonic distortion: <0.005%
  • Dynamic range:100dB
  • Input impedance:10K-Ohms
  • Maximum input: +10dB
  • Gain:52dB
  • Clip level output:+15dBu
  • Output impedance:300 Ohms
  • Equivalent input noise: -120dBu
  • Noise floor:-85dBu
  • Intermodulation distortion:<0.005%
  • Phase deviation:8° @50Hz
  • Common mode rejection:-73dB @55Hz
  • FX loop input impedance:100K
  • FX loop output impedance:3000 Ohms
  • Microphone input: Microphone gain
  • Low frequency EQ
  • High frequency EQ
  • 48V Phantom* (40V)
  • Effects loop: Send level
  • Receive level
  • 180° polarity reverse
  • Dry-wet mix
  • Switches:Footswitch-1: effects loop in/out
  • Footswitch-2 full wet or mute*
  • Side access: sets footswitch-2 to all wet or mute
  • Ground Lift: disconnects pin-1 at XLR output
  • Polarity: 180° signal polarity reverse switch
  • Input pad:Autopadding - input automatically pads as gain is reduced
  • Output:Pin 1 ground, Pin 2 (+), Pin 3 (-)
  • Construction: 14 gauge steel chassis and outer shell
  • Finish:Baked enamel
  • Power supply: Center positive
  • Power draw: 100mA
  • Warranty: Radial 3-year, transferable
  • Specifications are subject to change without notice

Customer Reviews

Write Your Own Review

You're reviewing: Voco-Loco Effects Switcher

How do you rate this product? *

  1 star 2 stars 3 stars 4 stars 5 stars